↑↓ to move ↵ to open Esc to close Browse all tools

Pork Tenderloin Cooking Time

Pork tenderloin is the quickest roast on the chart. USDA gives 20 to 27 minutes at 425 to 450 °F for a tenderloin of ½ to 1½ lb, to 145 °F, so the time barely depends on the weight and two tenderloins side by side take about as long as one.

20 to 27 min

For one tenderloin of ½ to 1½ lb, in a 425 °F (218 °C) oven. Rest 5 min (at least 3). USDA safe minimum: 145 °F (63 °C), then rest at least 3 min.

Runs on your device. Nothing you enter is sent to a server.

Pork tenderloin: time per piece

Minutes in a 425 °F (218 °C) oven, from the same chart and heat model the meat cooking time calculator uses. The chart gives one time for one tenderloin of ½ to 1½ lb, whatever the exact weight. Typical estimates: the thermometer decides.

PieceUSDA minimum 145 °FHigher end 160 °F
tenderloin of ½ to 1½ lb20 to 27 min23 to 32 min

Roasting pork tenderloin

Because the chart gives one total time for the whole weight range, this page has no weight table. The table below shows the time to the USDA minimum of 145 °F and, from the calculator’s heat model, the longer time to 160 °F, the top of the National Pork Board range for tenderloin.

A tenderloin is thin and lean, so the window between done and dry is short. Start checking at 20 minutes with the probe in the thickest part. Let it rest 5 minutes, at least 3, before slicing. If you roast two, lay them in one layer with space between them so the hot air reaches all sides.

Temperatures for pork tenderloin

USDA recommends 145 °F with a 3-minute rest for whole cuts of pork; the National Pork Board gives 145 to 160 °F for loin, tenderloin and chops.

DonenessTake out atNote
USDA minimum145 °F (63 °C)rest at least 3 min
Higher end160 °F (71 °C)top of the Pork Board range

USDA safe minimum internal temperatures: 145 °F for whole cuts of beef, pork, lamb and veal, measured before the meat comes out, then a rest of at least 3 minutes; 160 °F for ground meat; 165 °F for all poultry and for stuffing. The food safety temperatures guide has the full list.

Resting pork tenderloin

Rest: 5 min (at least 3). USDA asks for a rest of at least 3 minutes for whole cuts of pork; a few more minutes keep the juices in the meat when you slice. Measure in the thickest part of the meat, away from bone, fat and gristle, and clean the probe between readings.

Other cuts

The times come from the USDA roasting charts for rib roast, pork, leg of lamb and chicken, the Beef Checkoff roasting chart for tenderloin and the National Pork Board figures the calculator quotes. For another weight, Celsius, a doneness outside the table or a finish-by schedule, open the meat cooking time calculator; for a whole bird by weight, the turkey cooking time calculator.

Sources

Frequently asked questions

How long does a 1 lb pork tenderloin take at 425 °F?

About 20 to 27 minutes to 145 °F, the same as the USDA chart gives for any tenderloin from ½ to 1½ lb. Start checking at 20 minutes.

What temperature is pork tenderloin done at?

145 °F in the thickest part, then a rest of at least 3 minutes, by USDA. The center may be slightly pink. The National Pork Board gives 145 to 160 °F; at 160 °F it is firmer and paler.

Do two pork tenderloins take longer than one?

Not much. The chart time is per piece, so two tenderloins in one layer with space around them take about as long as one. Check each with the thermometer.

Should I sear pork tenderloin before roasting?

The chart time is for roasting alone. A quick sear in a hot pan before the oven adds color; it also adds heat, so start checking a little earlier.