↑↓ to move ↵ to open Esc to close Browse all tools

Energy and cars guide

Stopping Distance by Speed: Reaction, Braking and Total

A car does not stop where the driver decides to stop. It first travels on at full speed while the driver reacts, then slides to a halt over a distance that grows with the square of speed. The UK Highway Code publishes the clearest table of both parts. Here are its numbers, the two formulas behind them, what they assume, and the same arithmetic run for US speed limits.

The Highway Code table

The UK Highway Code splits each stopping distance into thinking distance, covered between seeing a hazard and pressing the brake, and braking distance, covered while the car slows to zero. Its figures, which it calls a general guide:

SpeedThinkingBrakingTotalTotal (ft)
20 mph6 m6 m12 m40 ft
30 mph9 m14 m23 m75 ft
40 mph12 m24 m36 m118 ft
50 mph15 m38 m53 m175 ft
60 mph18 m55 m73 m240 ft
70 mph21 m75 m96 m315 ft

The Code also counts them in car lengths, using an average car of 4 metres: three car lengths at 20 mph, six at 30 and twenty-four at 70. It adds that the real distance depends on your attention, the road surface, the weather and the condition of your vehicle.

The two formulas

Thinking distance
speed × reaction time
Braking distance
speed² ÷ (2 × deceleration)

Use metres per second for speed and seconds for time. One mph is exactly 0.44704 m/s, because a mile is defined as 1,609.344 metres. At 30 mph the car moves 13.4 metres every second, which is why even a short hesitation adds several metres. The speed converter does the mph, km/h and m/s step for any speed.

The first formula is linear: twice the speed, twice the thinking distance. The second is quadratic: twice the speed, four times the braking distance. That is the whole reason the bars in the Highway Code diagram stretch so fast. From 30 to 60 mph, thinking distance doubles from 9 to 18 metres while braking distance goes from 14 to 55 metres, close to four times.

What the table assumes

The Code does not print its assumptions, but they can be worked out from its own numbers. Divide each thinking distance by the speed to get the reaction time, and rearrange the braking formula to get the deceleration:

SpeedImplied reactionImplied deceleration
20 mph0.67 s6.66 m/s²
30 mph0.67 s6.42 m/s²
40 mph0.67 s6.66 m/s²
50 mph0.67 s6.57 m/s²
60 mph0.67 s6.54 m/s²
70 mph0.67 s6.53 m/s²

Every row implies the same reaction time of about 0.67 seconds and a deceleration close to 6.6 m/s², which is about 0.67 of the acceleration of gravity. So the table describes an alert driver and a car braking firmly on a dry road. A longer reaction, a wet road or worn tires all push the totals up.

Your own reaction time can be measured with the reaction time test. Keep in mind what it measures: how fast you click when you are already waiting for the screen to change. On the road you first have to notice the hazard and decide to brake, so the test result is a best case.

A worked model for US speed limits

The same two formulas, run for typical US speed limits. Assumptions: the deceleration implied by the Highway Code table, 6.56 m/s², and two reaction times, the 0.67 seconds the table implies and a slower 1.5 seconds for a driver who is distracted or has to judge the situation first. The results are arithmetic, not measurements.

SpeedBrakingTotal, 0.67 sTotal, 1.5 s
25 mph31 ft56 ft86 ft
35 mph61 ft96 ft138 ft
45 mph101 ft145 ft200 ft
55 mph151 ft205 ft272 ft
65 mph211 ft275 ft354 ft
75 mph281 ft355 ft446 ft

At 65 mph the slower reaction adds 79 feet before the brakes even engage. That is the cheapest distance to win back: it costs nothing but attention. The speed, distance and time calculator shows how far you travel at any speed in any number of seconds.

The two-second gap

Rule 126 of the Highway Code says to leave at least a two-second gap to the vehicle in front on high-speed roads and in tunnels with reduced visibility. It says the gap should be at least doubled on wet roads and up to ten times greater on icy roads. Here is how far two seconds is, next to the full stopping distance from the table:

SpeedTwo secondsStopping distance
20 mph59 ft40 ft
30 mph88 ft75 ft
40 mph117 ft118 ft
50 mph147 ft175 ft
60 mph176 ft240 ft
70 mph205 ft315 ft

At 20 and 30 mph two seconds is longer than the whole stopping distance; at 40 mph the two are about equal, and above that the gap is shorter. It works because the car in front also needs distance to stop, so you mainly need room to react. It fails when the car in front stops faster than a braking car would, for example in a collision. To count the gap, pick a fixed point such as a sign, and count from when the car in front passes it until you do.

What to take from the numbers

  • Speed costs more than you expect. 10 mph more on a fast road adds far more braking distance than 10 mph more in town, because braking grows with the square of speed.
  • Reaction time is half the story at low speed. At 20 mph thinking and braking distance are equal in the table, 6 metres each.
  • Wet and icy roads change the deceleration, not the reaction. Lower deceleration stretches only the braking part, which is why the Code multiplies the gap for wet and icy roads.
  • The table is a guide. The Code says so itself. Real stops depend on driver, tires, brakes, load and surface.

Frequently asked questions

What is the stopping distance at 60 mph?

The UK Highway Code gives 73 metres, or 240 feet, for a car at 60 mph: 18 metres of thinking distance and 55 metres of braking distance. It calls the figures a general guide that depends on attention, road surface, weather and the vehicle.

Why does stopping distance grow faster than speed?

The thinking part grows in step with speed, but the braking part grows with the square of speed. Double the speed and the car covers twice the distance before you brake, then needs four times the distance to stop. In the Highway Code table, going from 30 to 60 mph doubles thinking distance from 9 to 18 metres and roughly quadruples braking distance from 14 to 55 metres.

What reaction time does the Highway Code assume?

The Code does not state one, but its thinking distances imply it: 6 metres at 20 mph is about 0.67 seconds, and every row works out to the same value. That is a short time for an alert driver. Many real situations take longer, which the table on this page shows with 1.5 seconds.

Is the two-second rule enough to stop?

The two-second gap in Highway Code rule 126 is not a full stopping distance. It is meant to give you time to react if the car in front brakes, since that car also needs distance to stop. The Code says to at least double the gap on wet roads and allow up to ten times the gap on icy roads.

Do these numbers apply in the US?

The physics is the same everywhere. The table figures come from the UK Highway Code because it publishes them with the split into thinking and braking. This page also gives a worked model for typical US speed limits, with its assumptions stated, so you can see how the totals change with reaction time.

Sources